# Stagehand AC - AKA: The Classic

The Stagehand AC - The "Classic" - comes in three varieties:

* A800
* A700
* Durapulse

Follow these instructions to factory restore a [Classic with an A700 or A800 VFD](/docs/stagehand/stagehand-parameters/all-clear-parameter-clear.md), and these instructions for [#durapulse-factory-restore](#durapulse-factory-restore "mention").

## Stagehand AC "Classic" A800

{% hint style="danger" %}
**Set Parameter 77 = 2 before jumping into manually entering parameters!**
{% endhint %}

<table><thead><tr><th width="88">No.</th><th>Name</th><th width="351">Description</th><th>A800 Setting</th></tr></thead><tbody><tr><td>1</td><td>Maximum frequency</td><td>Max output frequency</td><td>120</td></tr><tr><td>7</td><td>Acceleration time</td><td>0 seconds</td><td>0</td></tr><tr><td>8</td><td>Deceleration time</td><td>0 seconds</td><td>0</td></tr><tr><td>9</td><td>Electronic thermal O/L relay</td><td>Nameplate FLA Rating</td><td>17</td></tr><tr><td>13</td><td>Starting frequency</td><td>Motor won’t start until the speed signal is at least this value.</td><td>0.5</td></tr><tr><td>30</td><td>Regenerative function selection</td><td>External brake resistor, L1/L2/L3 power source</td><td>1</td></tr><tr><td>70</td><td>Special regenerative brake duty</td><td>duty cycle of the braking resistor</td><td>10</td></tr><tr><td>71</td><td>Applied motor</td><td>Other mfg. standard motor</td><td>3</td></tr><tr><td>72</td><td>PWM frequency selection</td><td>Reduces output noise</td><td>15</td></tr><tr><td>73</td><td>Analog input selection</td><td>+/-10vdc with reversing enabled</td><td>14</td></tr><tr><td>77</td><td>Parameter write selection</td><td>Allow parameter writes regardless of operation status.</td><td>2</td></tr><tr><td>79</td><td>Operation mode selection</td><td>Keypad disabled, external control</td><td>0</td></tr><tr><td>80</td><td>Motor capacity</td><td>Motor nameplate kilowatt rating</td><td>3.7</td></tr><tr><td>81</td><td>Motor poles</td><td>Number of motor poles</td><td>4</td></tr><tr><td>83</td><td>Rated motor voltage</td><td>Nameplate motor voltage</td><td>230</td></tr><tr><td>84</td><td>Rated motor frequency</td><td>Nameplate frequency</td><td>60</td></tr><tr><td>96</td><td>Auto tuning setting/status</td><td>1 to begin cycle</td><td>0</td></tr><tr><td>125</td><td>Terminal 2 frequency setting gain frequency</td><td>Set what 100% = in hertz (overspeed) <strong>**This should be used with setting the C4 value**</strong></td><td>60</td></tr><tr><td>196</td><td>Relay #2 output</td><td>Brake released when drive is running</td><td>0</td></tr><tr><td>252</td><td>Override bias</td><td>Percentage of analog signal to use for speed signal **<strong>adjust this to overspeed motor without setting Pr.C4</strong>**</td><td>100</td></tr><tr><td>414</td><td>PLC Brake Logic</td><td>"0" turns this off</td><td>0</td></tr><tr><td>800</td><td>Control Method</td><td>Real sensorless vector control</td><td>10</td></tr><tr><td>C3</td><td>Terminal 2 frequency setting bias</td><td>Making 0% = 0Hz<br><a href="/pages/GvPji5arCM20lhPJIgkl">See the instructions on setting the C3 value.</a></td><td><a href="/pages/GvPji5arCM20lhPJIgkl">TBD</a></td></tr><tr><td>C4</td><td>Terminal 2 Gain Frequency</td><td>C4 - Enter the value on the Stagehand cabinet or <a href="/pages/ZoQLslNEmgHxRhgWoq8F">check out the guide</a></td><td><a href="/pages/ZoQLslNEmgHxRhgWoq8F">TBD</a></td></tr></tbody></table>

## Stagehand AC "Classic" A700

{% hint style="danger" %}
**Set Parameter 77 = 2 before jumping into manually entering parameters!**
{% endhint %}

<table><thead><tr><th width="89">No.</th><th width="169">Name</th><th width="337">Description</th><th>A700 Setting</th></tr></thead><tbody><tr><td>1</td><td>Maximum frequency</td><td>Max output frequency</td><td>120</td></tr><tr><td>7</td><td>Acceleration time</td><td>0 seconds</td><td>0</td></tr><tr><td>8</td><td>Deceleration time</td><td>0 seconds</td><td>0</td></tr><tr><td>9</td><td>Electronic thermal O/L relay</td><td>Nameplate FLA Rating</td><td>17</td></tr><tr><td>13</td><td>Starting frequency</td><td>Motor won’t start until the speed signal is at least this value.</td><td>0.5</td></tr><tr><td>30</td><td>Regenerative function selection</td><td>External brake resistor, L1/L2/L3 power source</td><td>1</td></tr><tr><td>70</td><td>Special regenerative brake duty</td><td>duty cycle of the braking resistor</td><td>10</td></tr><tr><td>71</td><td>Applied motor</td><td>Other mfg. standard motor</td><td>3</td></tr><tr><td>72</td><td>PWM frequency selection</td><td>Reduces output noise</td><td>15</td></tr><tr><td>73</td><td>Analog input selection</td><td>+/-10vdc with reversing enabled</td><td>14</td></tr><tr><td>77</td><td>Parameter write selection</td><td>Allow parameter writes regardless of operation status.</td><td>2</td></tr><tr><td>79</td><td>Operation mode selection</td><td>Keypad disabled, external control</td><td>0</td></tr><tr><td>80</td><td>Motor capacity</td><td>Motor nameplate kilowatt rating</td><td>3.7</td></tr><tr><td>81</td><td>Motor poles</td><td>Number of motor poles</td><td>4</td></tr><tr><td>83</td><td>Rated motor voltage</td><td>Nameplate motor voltage</td><td>230</td></tr><tr><td>84</td><td>Rated motor frequency</td><td>Nameplate frequency</td><td>60</td></tr><tr><td>96</td><td>Auto tuning setting/status</td><td>1 to begin cycle</td><td>0</td></tr><tr><td>125</td><td>Terminal 2 frequency setting gain frequency</td><td>Set what 100% = in hertz (overspeed) <strong>**This should be used with setting the C4 value**</strong></td><td>60</td></tr><tr><td>196</td><td>Relay #2 output</td><td>Brake released when drive is running</td><td>0</td></tr><tr><td>252</td><td>Override bias</td><td>Percentage of analog signal to use for speed signal **<strong>adjust this to overspeed motor without setting Pr.C4</strong>**</td><td>100</td></tr><tr><td>414</td><td>PLC function operation selection</td><td>PLC program to load</td><td>0</td></tr><tr><td>800</td><td>Control Method</td><td>Real sensorless vector control</td><td>10</td></tr><tr><td>C4</td><td>Terminal 2 Gain Frequency</td><td>C4 - Enter the value on the Stagehand cabinet or <a href="https://github.com/creativeconners/PublicDocumentation/blob/main/stagehand/stagehand-parameters/broken-reference/README.md">check out the guide</a></td><td>TBD</td></tr></tbody></table>

## Stagehand AC "Classic" Durapulse

### Durapulse Factory Restore

**Set parameter:** 9.08 = 99.

Yup, that's it!

### Restore Parameters on Stagehand AC Durapulse <a href="#h.b4wszrtbbu6p" id="h.b4wszrtbbu6p"></a>

**MANUALLY SETTING PARAMETER VALUES**

The table below shows the values for the Creative Conners stock parameters.

1. Press **PROGRAM** once
2. Use the **UP** and **DOWN** arrows to select each parameter to set
3. Press the **SET** button and change the value with the up and down arrow
4. Once to the correct value press **ENTER**
   * the display will flash **VALUE ACCEPTED** and then will show the new value
5. Repeat the steps for each parameter
6. Once completed, **cycle the power** on the drive

You may notice that some of the parameter values are NOT CHANGED from the stock values and that is OK. It is important to confirm these values are set correctly.

### **STAGEHAND AC (DURAPULSE GS3) STOCK PARAMETER VALUES**

<table data-header-hidden data-full-width="true"><thead><tr><th width="141.5"></th><th></th><th></th><th width="100"></th></tr></thead><tbody><tr><td><strong>No.</strong></td><td><strong>Name</strong></td><td><strong>Description</strong></td><td><strong>Setting</strong></td></tr><tr><td>0.00</td><td>Motor Voltage</td><td>voltage</td><td>230V</td></tr><tr><td>0.01</td><td>Motor Amps</td><td>full load amps</td><td>17</td></tr><tr><td>0.02</td><td>Motor Frequency</td><td>hertz</td><td>60</td></tr><tr><td>0.03</td><td>Motor Base RPM</td><td>rpm</td><td>1750</td></tr><tr><td>0.04</td><td>Motor Max RPM</td><td>Motor RPM at full speed (100%)<br>**<strong>adjust to overspeed**</strong></td><td>1750</td></tr><tr><td>1.00</td><td>Stop method</td><td>ramp to stop</td><td>0</td></tr><tr><td>1.01</td><td>Accel time</td><td>seconds</td><td>0.1</td></tr><tr><td>1.02</td><td>Decel time</td><td>seconds</td><td>0.1</td></tr><tr><td>2.00</td><td>V/Hz setting</td><td>High start torque</td><td>1</td></tr><tr><td>2.10</td><td>Control mode</td><td>sensorless vector</td><td>2</td></tr><tr><td>3.00</td><td>Source of operation</td><td>External, keypad disabled</td><td>2</td></tr><tr><td>3.01</td><td>D1-D2 input</td><td>D1 run/stop D2 rev/fwd</td><td>1</td></tr><tr><td>3.11</td><td>Relay output</td><td>above desired frequency</td><td>4</td></tr><tr><td>3.16</td><td>desired frequency</td><td>hertz</td><td>0.1</td></tr><tr><td>4.00</td><td>Source of freq. command</td><td>+/-10vdc</td><td>6</td></tr><tr><td>4.03</td><td>analog input gain</td><td>percent</td><td>112</td></tr><tr><td>4.04</td><td>Reverse motion enable</td><td>enable reverse motion</td><td>1</td></tr><tr><td>6.02</td><td>Momentary Power Loss</td><td>continue operation after restore, speed from reference signal</td><td>1</td></tr><tr><td>6.04</td><td>Auto voltage regulation</td><td>disable auto-voltage regulation</td><td>1</td></tr><tr><td>6.05</td><td>Over-voltage Stall Prevention</td><td>disable over-voltage stall prevention</td><td>1</td></tr><tr><td>6.12</td><td>Max Allowable Power Loss Time</td><td>seconds</td><td>5</td></tr><tr><td>8.00</td><td>Display function</td><td>output frequency</td><td>0</td></tr><tr><td>9.08</td><td>Factory reset</td><td>Set to 99 to restore parameters to factory defaults</td><td>0</td></tr></tbody></table>


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.creativeconners.com/docs/stagehand/stagehand-parameters/stagehand-ac-aka-the-classic.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.